When you are preparing to print a text file, you have instructed the printer but the light on the printer is still not working, or in other words the light on the printer does not light or the light on the printer is blinking. flashes continuously. When this error occurs, I personally realize that many printer users do not know how to fix the error and they do not know the main cause of the error.
So what causes this error? And how to fix the error? Please refer to the article below, I will share with you how to fix the error The printer light does not light / blink.
Introduction and How to fix the printer light blinking or not lighting
Next, we will instruct readers to perform each of the most specific actions to fix the printer light is blinking or not glowing, not working.
How you find good products: best copier machine
How to fix printer light blinking or not lighting
When a user executes a print job and the printer is not working, or the printer light blinks continuously or does not light up causing you to worry and do not know how to do it, here are the three main causes. errors and how to fix those errors that I will share for readers:
1. CASE 1: THE MACHINE STARTED, RUNS TO RUN MULTIPLE AND FLASHED 2 LIGHTS AT THE SAME TIME
The cause of the error:
+ Due to your printer's hardware dirty.
Error due to the ink line being stuck when the machine starts up
+ Error related to main board.
+ Due to the printer's optical eye is dirty.
The reason is that the ink nozzles are damaged.
Error due to dirty or scratched tape measure.
How to fix: This error is caused by the Hardware in the printer. For those of you whose printer makes this mistake, you should open the printer and clean and clean it. Besides, you also need to pay attention to reinstall each part on the machine in accordance with the correct technique. If the situation is more severe than necessary, you will have to replace the damaged parts on that machine.
2. CASE 2: IF ONE LIGHTS FLASH AND ONE LIGHTNING IS NOT ON
Find out what caused the error:
+ Maybe because the printer is in the state of receiving data, then the green light will blink slowly.
Fix: Wait a moment for the loading of the data to finish and printing will start.
+ Or the reason is that in the printing process you accidentally right-clicked the Cancel button.
Error correction: Please quickly press the Resume button to resume printing.
+ Or it could be that your paper tray is no longer paper, or the machine is jammed
How to fix this: You need to add more paper to the tray. With paper jams, you should avoid pulling the paper directly out of the printer, as DRUM damage will result. When this happens, you should remove the toner cartridge from the printer, then pull out the jammed paper, and then repeat the cartridge.
3. CASE 3: START THE MACHINE, THE MACHINE DOESN'T RUN WITH TWO FLASHING.
Instructions to fix the printer blinking or not lit + Figure 4
Cause of the error: The printer has overflowed which causes the printer to hang.
How to fix: Users need to restart (Restart) the printer. After restarting, but the machine still does not work as usual, you will need to use the software to reset the printer.
For those of you who are using Epson's printer line, you can download / download SSC Utility 4.3 software. When starting the software, a message will appear on the system.
When the message on the system displays a Maintanice needed, people go to the Protection counter -> Reset Protection Counter, and then wait until the message Has the ink pad been replaced, choose Yes.
If the message on the system shows up with the form Locked out, go to Protection counter -> Clearcounter overflow. Next, select Extra -> Soft reset and wait a few seconds for the printer to reset. Finally, you select the Reset Protection Counter function as above, and turn off the power and restart the printer.
In the above article, I have listed the cases, the causes of the alternating flash error, or the light does not light on the printer and how to fix those errors for everyone to refer. I hope this article will be of help to you when encountering similar problems with printers. Thank you for taking the time to read the article and do not forget to click the Share button to share this article for everyone.
In addition, if you have any comments on the above issue, you can comment through the comment box below.
Good luck!